|
TUTHILL CC Series Close Coupled Pumps: CC Series
CC系列循環泵 - 采用機械密封的泵結構緊湊并直接連接在標準的NEMA 或 IEC電機上。應用：潤滑油，燃油輸送，過濾
Models C2E, C2EN, C2F, and C2FA
Model C2E and C2F pumps are sleeve bushing lip seal units designed for direct drive service. Model C2E comes with the foot assembled
to the pump. Model C2F is a flange mount pump. Model C2FA pumps are similar to model C2F but are supplied without a seal. Model
C2EN pumps are sleeve and ball bearing units with a lip seal and mounting foot designed for indirect (belt, chain, gear) drive. The seal
chamber on these pumps is vented to the suction side of the pumping zone. Therefore, the pump must operate in the direction for
which it is assembled. All models are available in five sizes, ranging in capacity from 6 to 84 gpm with differential pressures to 100 psi.
The maximum discharge pressure capability is 100 psi.
Model C2B
Model C2B is a flange-mount pump with two sleeve type bushings and a mechanical seal. The seal chamber on these pumps is vented
to the suction side of the pumping zone. Therefore, the pump must operate in the direction for which it is assembled. This pump is
available in five sizes, with capacities from 6 to 84 gpm and differential pressures to 150 psi. The maximum discharge pressure capability
is 300 psi. A mounting foot is optional.
Model C2G
Model C2G is equipped with spring-loaded V-type graphite-impregnated PTFE packing. Model C2G pumps have the packing chamber
vented to the suction side of the pumping zone. Therefore, the pump must operate in the direction for which it is assembled. There
are five sizes, ranging in capacity from 6 to 84 gpm with differential pressures to 100 psi. The maximum discharge pressure capability
is 125 psi.
Model CK1B
Model CK1B pumps are equipped with a mechanical seal and incorporate heavy-duty features, including special double-bearing
construction with an inboard double ball bearing and an outboard roller bearing. There are five sizes, with capacities from 6 to 84
gpm and differential pressures to 250 psi. The maximum discharge pressure capability is 300 psi. A mounting foot is optional. The seal
chamber is vented to the suction side. Therefore, the pump must operate in the direction for which it is assembled.
Model CC
Model CC pumps are designed to mount directly to NEMA 56, 143TC or 145TC C Face motors. They are equipped with a mechanical seal
and will pump equally well in either direction of rotation (unless equipped with an internal relief valve). These pumps are available in
four sizes, with capacities from 9 to 30 gpm. They can handle inlet pressures to 25 psi and differential pressures to 100 psi.
Model: 009, 015, 020, 030
CC Series Specifications |
Model |
Port Number |
Nominal Flow Capacity |
Speed (max) |
009 |
1 |
9.4 gpm* |
35.5 lpm * |
1800 RPM |
015 |
1 1/2 |
16.6 gpm* |
62.8 lpm* |
1800 RPM |
020 |
1 1/2 |
22.2 gpm* |
84.0 lpm* |
1800 RPM |
030 |
1 1/2 |
32.5 gpm* |
123 lpm* |
1800 RPM |
*Rate at 750 ssu / 50 psi
Applicationh產品應用：
Lubrication, Fluid Transfer, Filtration, Lube Oil, Fuel Oil, Glycol Solutions (Anti-Freeze), Water Treatment, Polymers, Filtering Waste Oil
潤滑、流體輸送、過濾、潤滑油、燃油、乙二醇溶液（防凍）、水處理、聚合物、過濾廢油
Brochures
|
